Перейти к содержимому
New

DeepSeek V4.1 Flash free for 7 days: 10M tokens a day after a top-up of $10 or more. Until Nov 30.

How it works
aeondave/uart-consoleМобильные устройства, прошивки и железо

uart-console

⁨Identification, connection, and exploitation of UART serial consoles (U-Boot/Barebox interrupt, bootargs patching) during hardware assessments.⁩

v2026.11.13-21cd5683 установки+3 за 7 дней39 Звездысинхронизировано 10 часов назад

Установка

Ещё нет NotHoly CLI? Сначала установите её.

$ curl -fsSL https://notholy.com/install.sh | sh
$ notholy skills install aeondave/uart-console

Пишет в ⁦~/.notholy/skills⁩ после проверки подписи и SHA-256.

ПодписьПодписано, ed25519
0UFcSicHSD…xdVbGACg==CLI проверяет SHA-256 и подпись, прежде чем записать хоть один файл.
Пакет288690fe…b218d111
288690fe3121…7355b218d1111 файл · ⁦1.2 KB⁩
ПроверкаСредний1 замечание
  • Лицензия не найдена
Вся проверка
Источникgithub.com/AeonDave/malskill/tree/main/offensive-hardware/uart-console@21cd568

Эта запись еще не переведена на русский, поэтому показан текст на другом языке: English.

Use when physical access is available, and you need an interactive root shell without desoldering chips or risking firmware corruption.

1. Pin identification

  • Visual: Look for 3-4 unpopulated through-holes or test pads near the SoC.
  • Multimeter:
    1. GND: 0 V (continuity with shielding).
    2. VCC: 3.3 V or 5 V (constant).
    3. TX: Idle HIGH (3.3 V), fluctuates during boot.
    4. RX: High-impedance (floats to ~0 V or pull-up).
  • JTAGulator: Use UART scan capability if pads are unlabeled/dense.

2. Connection

Rule: Do NOT connect VCC if the device is self-powered. This causes voltage collision.

  • Connect: GND → GND, RX → TX_pad, TX → RX_pad.
bash
# Try standard baud rates: 115200, 57600, 38400, 19200, 9600
screen /dev/ttyUSB0 115200
# or
minicom -D /dev/ttyUSB0 -b 115200

If output is garbled, cycle through baud rates. Check logic analyzer for precise rate if needed.

3. Bootloader exploitation (U-Boot)

Monitor output closely on power-on.

  • Prompt: Hit any key to stop autoboot. Press immediately.

Key U-Boot commands:

bash
printenv         # Dump environment variables (credentials, boot paths, keys)
md 0x80000000    # Hex dump memory (hunt for loaded keys/passwords)
boot             # Resume boot process

Drop to shell (root init bypass):

bash
# Replace normal init with a shell to bypass authentication
setenv bootargs 'console=ttyS0,115200 root=/dev/mtdblock2 init=/bin/sh'
boot

4. Secure boot bypass patterns

If U-Boot enforces verified boot (CONFIG_SECUREBOOT):

  1. Read signing keys from NAND/SPI mapping (sometimes unprotected).
  2. Patch U-Boot env locally to drop CONFIG_SECUREBOOT (requires SPI write).
  3. Voltage glitching on SoC VCC rail exactly during signature verification branching.

Файлы этой версии

Права

ПравоЗаявленоНайдено проверкой
Читает файлыНетНет
Пишет файлыНетНет
Выполняет команды shellДаДа
Ходит в сетьНетНет
Использует коннекторыНетНет
Управляет браузеромНетНет

Замечания проверки

Проверено 13 нояб. 2026 г.

  1. СредняяЛицензия · Лицензия не найдена

Чистая проверка снижает риск, но не доказывает, что пакет безопасен. Читайте то, что ставите.

ВерсияОпубликованаКоммитSHA-256ПодписьИзменение прав
v2026.11.13-21cd56813 нояб. 2026 г.21cd568288690feПодписана–

Спрашивайте обо всём, что позволяет ваш скоуп.

Создайте аккаунт, пополните баланс и задайте первый вопрос в чате или в терминале.

  1. 1/3

    Создайте аккаунт

    Личный или для компании. Позже можно перейти на аккаунт компании без потери баланса и ключей.

    ЛичныйКомпания
  2. 2/3

    Пополните баланс

    Картой. Оплата за токены, без подписки.

    $5.00минимальное пополнение
  3. 3/3

    Спрашивайте

    В чате, или установите CLI и выполните notholy login в терминале.

    $ notholy login