דילוג לתוכן
New

DeepSeek V4.1 Flash free for 7 days: 10M tokens a day after a top-up of $10 or more. Until Nov 30.

How it works
aeondave/uart-consoleמובייל, קושחה וחומרה

uart-console

⁨Identification, connection, and exploitation of UART serial consoles (U-Boot/Barebox interrupt, bootargs patching) during hardware assessments.⁩

v2026.11.13-21cd5683 התקנות⁦+3⁩ ב-7 ימים39 כוכביםסונכרן לפני 10 שעות

התקנה

עדיין אין לכם את ה-CLI של NotHoly? התקינו אותו קודם.

$ curl -fsSL https://notholy.com/install.sh | sh
$ notholy skills install aeondave/uart-console

נכתב אל ⁦~/.notholy/skills⁩ אחרי בדיקת החתימה וה-SHA-256.

חתימהחתום, ed25519
0UFcSicHSD…xdVbGACg==ה-CLI בודק את ה-SHA-256 ואת החתימה לפני שהוא כותב קובץ כלשהו.
חבילה288690fe…b218d111
288690fe3121…7355b218d111קובץ אחד · ⁦1.2 KB⁩
סריקהבינוניממצא אחד
  • לא נמצא רישיון
לסריקה המלאה
מקורgithub.com/AeonDave/malskill/tree/main/offensive-hardware/uart-console@21cd568

הפריט הזה עדיין לא נכתב בעברית, ולכן הוא מוצג בשפה אחרת: English.

Use when physical access is available, and you need an interactive root shell without desoldering chips or risking firmware corruption.

1. Pin identification

  • Visual: Look for 3-4 unpopulated through-holes or test pads near the SoC.
  • Multimeter:
    1. GND: 0 V (continuity with shielding).
    2. VCC: 3.3 V or 5 V (constant).
    3. TX: Idle HIGH (3.3 V), fluctuates during boot.
    4. RX: High-impedance (floats to ~0 V or pull-up).
  • JTAGulator: Use UART scan capability if pads are unlabeled/dense.

2. Connection

Rule: Do NOT connect VCC if the device is self-powered. This causes voltage collision.

  • Connect: GND → GND, RX → TX_pad, TX → RX_pad.
bash
# Try standard baud rates: 115200, 57600, 38400, 19200, 9600
screen /dev/ttyUSB0 115200
# or
minicom -D /dev/ttyUSB0 -b 115200

If output is garbled, cycle through baud rates. Check logic analyzer for precise rate if needed.

3. Bootloader exploitation (U-Boot)

Monitor output closely on power-on.

  • Prompt: Hit any key to stop autoboot. Press immediately.

Key U-Boot commands:

bash
printenv         # Dump environment variables (credentials, boot paths, keys)
md 0x80000000    # Hex dump memory (hunt for loaded keys/passwords)
boot             # Resume boot process

Drop to shell (root init bypass):

bash
# Replace normal init with a shell to bypass authentication
setenv bootargs 'console=ttyS0,115200 root=/dev/mtdblock2 init=/bin/sh'
boot

4. Secure boot bypass patterns

If U-Boot enforces verified boot (CONFIG_SECUREBOOT):

  1. Read signing keys from NAND/SPI mapping (sometimes unprotected).
  2. Patch U-Boot env locally to drop CONFIG_SECUREBOOT (requires SPI write).
  3. Voltage glitching on SoC VCC rail exactly during signature verification branching.

הקבצים בגרסה הזו

הרשאות

הרשאההוצהרנמצא בסריקה
קורא קבציםלאלא
כותב קבציםלאלא
מריץ פקודות shellכןכן
משתמש ברשתלאלא
משתמש במחבריםלאלא
שולט בדפדפןלאלא

ממצאי הסריקה

נבדק ב-13 בנוב׳ 2026

  1. בינוניתרישיון · לא נמצא רישיון

סריקה נקייה מורידה את הסיכון, אבל לא מוכיחה שהחבילה בטוחה. כדאי לקרוא מה מתקינים.

גרסהפורסמהCommitSHA-256חתימהשינוי בהרשאות
v2026.11.13-21cd56813 בנוב׳ 202621cd568288690feחתומה–

שאלו כל מה שהסקופ מאפשר.

יוצרים חשבון, מוסיפים קרדיטים ושואלים את השאלה הראשונה בצ׳אט או בטרמינל.

  1. 1/3

    יצירת חשבון

    פרטי או חברה. אפשר לעבור לחשבון חברה אחר כך בלי לאבד יתרה או מפתחות.

    פרטיחברה
  2. 2/3

    הוספת קרדיטים

    בכרטיס אשראי. תשלום לפי טוקן, בלי מנוי.

    $5.00טעינה מינימלית
  3. 3/3

    שאלה ראשונה

    בצ׳אט, או להתקין את ה-CLI ולהריץ notholy login בטרמינל.

    $ notholy login