Vai al contenuto
New

DeepSeek V4.1 Flash free for 7 days: 10M tokens a day after a top-up of $10 or more. Until Nov 30.

How it works
aeondave/uart-consoleMobile, firmware e hardware

uart-console

⁨Identification, connection, and exploitation of UART serial consoles (U-Boot/Barebox interrupt, bootargs patching) during hardware assessments.⁩

v2026.11.13-21cd5683 installazioni+3 in 7 giorni39 Stellesincronizzato 10 ore fa

Installa

Non hai ancora la CLI di NotHoly? Installala prima.

$ curl -fsSL https://notholy.com/install.sh | sh
$ notholy skills install aeondave/uart-console

Scrive in ⁦~/.notholy/skills⁩ dopo aver controllato la firma e lo SHA-256.

FirmaFirmato, ed25519
0UFcSicHSD…xdVbGACg==La CLI controlla lo SHA-256 e la firma prima di scrivere qualsiasi file.
Pacchetto288690fe…b218d111
288690fe3121…7355b218d1111 file · ⁦1.2 KB⁩
ScansioneMedio1 segnalazione
  • Nessuna licenza trovata
Vedi la scansione completa
Sorgentegithub.com/AeonDave/malskill/tree/main/offensive-hardware/uart-console@21cd568

Questa voce non è ancora scritta in italiano, quindi è mostrata in un'altra lingua: English.

Use when physical access is available, and you need an interactive root shell without desoldering chips or risking firmware corruption.

1. Pin identification

  • Visual: Look for 3-4 unpopulated through-holes or test pads near the SoC.
  • Multimeter:
    1. GND: 0 V (continuity with shielding).
    2. VCC: 3.3 V or 5 V (constant).
    3. TX: Idle HIGH (3.3 V), fluctuates during boot.
    4. RX: High-impedance (floats to ~0 V or pull-up).
  • JTAGulator: Use UART scan capability if pads are unlabeled/dense.

2. Connection

Rule: Do NOT connect VCC if the device is self-powered. This causes voltage collision.

  • Connect: GND → GND, RX → TX_pad, TX → RX_pad.
bash
# Try standard baud rates: 115200, 57600, 38400, 19200, 9600
screen /dev/ttyUSB0 115200
# or
minicom -D /dev/ttyUSB0 -b 115200

If output is garbled, cycle through baud rates. Check logic analyzer for precise rate if needed.

3. Bootloader exploitation (U-Boot)

Monitor output closely on power-on.

  • Prompt: Hit any key to stop autoboot. Press immediately.

Key U-Boot commands:

bash
printenv         # Dump environment variables (credentials, boot paths, keys)
md 0x80000000    # Hex dump memory (hunt for loaded keys/passwords)
boot             # Resume boot process

Drop to shell (root init bypass):

bash
# Replace normal init with a shell to bypass authentication
setenv bootargs 'console=ttyS0,115200 root=/dev/mtdblock2 init=/bin/sh'
boot

4. Secure boot bypass patterns

If U-Boot enforces verified boot (CONFIG_SECUREBOOT):

  1. Read signing keys from NAND/SPI mapping (sometimes unprotected).
  2. Patch U-Boot env locally to drop CONFIG_SECUREBOOT (requires SPI write).
  3. Voltage glitching on SoC VCC rail exactly during signature verification branching.

File di questa versione

Permessi

PermessoDichiaratoTrovato dalla scansione
Legge fileNoNo
Scrive fileNoNo
Esegue comandi shellSìSì
Usa la reteNoNo
Usa i connettoriNoNo
Controlla un browserNoNo

Segnalazioni della scansione

Rivisto il 13 nov 2026

  1. MediaLicenza · Nessuna licenza trovata

Una scansione pulita abbassa il rischio, ma non prova che il pacchetto sia sicuro. Leggi quello che installi.

VersionePubblicataCommitSHA-256FirmaCambio di permessi
v2026.11.13-21cd56813 nov 202621cd568288690feFirmata–

Chiedi tutto quello che il tuo perimetro consente.

Crea un account, aggiungi crediti e fai la prima domanda in chat o nel terminale.

  1. 1/3

    Crea l'account

    Privato o azienda. Puoi passare ad azienda in seguito senza perdere saldo o chiavi.

    PrivatoAzienda
  2. 2/3

    Aggiungi crediti

    Con carta. Paghi a token, senza abbonamento.

    $5.00ricarica minima
  3. 3/3

    Chiedi

    In chat, oppure installa la CLI ed esegui notholy login nel terminale.

    $ notholy login