Saltar al contenido
Nuevo

DeepSeek V4.1 Flash gratis por 7 días: 10M tokens al día tras una recarga de $10 o más. Hasta el 30/11.

Cómo funciona
aeondave/uart-consoleMóvil, firmware y hardware

uart-console

⁨Identification, connection, and exploitation of UART serial consoles (U-Boot/Barebox interrupt, bootargs patching) during hardware assessments.⁩

v2026.11.13-21cd5683 instalaciones+3 en 7 días39 Estrellassincronizado hace 10 horas

Instalar

¿Aún no tienes la CLI de NotHoly? Instálala primero.

$ curl -fsSL https://notholy.com/install.sh | sh
$ notholy skills install aeondave/uart-console

Escribe en ⁦~/.notholy/skills⁩ después de comprobar la firma y el SHA-256.

FirmaFirmado, ed25519
0UFcSicHSD…xdVbGACg==La CLI comprueba el SHA-256 y la firma antes de escribir cualquier archivo.
Paquete288690fe…b218d111
288690fe3121…7355b218d1111 archivo · ⁦1.2 KB⁩
EscaneoMedio1 hallazgo
  • No se encontró licencia
Ver el escaneo completo
Fuentegithub.com/AeonDave/malskill/tree/main/offensive-hardware/uart-console@21cd568

Esta entrada todavía no está escrita en tu idioma, así que aparece en English.

Use when physical access is available, and you need an interactive root shell without desoldering chips or risking firmware corruption.

1. Pin identification

  • Visual: Look for 3-4 unpopulated through-holes or test pads near the SoC.
  • Multimeter:
    1. GND: 0 V (continuity with shielding).
    2. VCC: 3.3 V or 5 V (constant).
    3. TX: Idle HIGH (3.3 V), fluctuates during boot.
    4. RX: High-impedance (floats to ~0 V or pull-up).
  • JTAGulator: Use UART scan capability if pads are unlabeled/dense.

2. Connection

Rule: Do NOT connect VCC if the device is self-powered. This causes voltage collision.

  • Connect: GND → GND, RX → TX_pad, TX → RX_pad.
bash
# Try standard baud rates: 115200, 57600, 38400, 19200, 9600
screen /dev/ttyUSB0 115200
# or
minicom -D /dev/ttyUSB0 -b 115200

If output is garbled, cycle through baud rates. Check logic analyzer for precise rate if needed.

3. Bootloader exploitation (U-Boot)

Monitor output closely on power-on.

  • Prompt: Hit any key to stop autoboot. Press immediately.

Key U-Boot commands:

bash
printenv         # Dump environment variables (credentials, boot paths, keys)
md 0x80000000    # Hex dump memory (hunt for loaded keys/passwords)
boot             # Resume boot process

Drop to shell (root init bypass):

bash
# Replace normal init with a shell to bypass authentication
setenv bootargs 'console=ttyS0,115200 root=/dev/mtdblock2 init=/bin/sh'
boot

4. Secure boot bypass patterns

If U-Boot enforces verified boot (CONFIG_SECUREBOOT):

  1. Read signing keys from NAND/SPI mapping (sometimes unprotected).
  2. Patch U-Boot env locally to drop CONFIG_SECUREBOOT (requires SPI write).
  3. Voltage glitching on SoC VCC rail exactly during signature verification branching.

Archivos de esta versión

Permisos

PermisoDeclaradoHallado en el escaneo
Lee archivosNoNo
Escribe archivosNoNo
Ejecuta comandos de shellSíSí
Usa la redNoNo
Usa conectoresNoNo
Controla un navegadorNoNo

Hallazgos del escaneo

Revisado el 13 nov 2026

  1. MediaLicencia · No se encontró licencia

Un escaneo limpio baja el riesgo, pero no prueba que el paquete sea seguro. Lee lo que instalas.

VersiónPublicadaCommitSHA-256FirmaCambio de permisos
v2026.11.13-21cd56813 nov 202621cd568288690feFirmada–

Pregunta todo lo que tu alcance permite.

Crea la cuenta, añade créditos y haz la primera pregunta en el chat o en la terminal.

  1. 1/3

    Crea la cuenta

    Individual o empresa. Puedes pasar a empresa después sin perder saldo ni claves.

    IndividualEmpresa
  2. 2/3

    Añade créditos

    Con tarjeta. Pagas por token, sin suscripción.

    $5.00recarga mínima
  3. 3/3

    Pregunta

    En el chat, o instala el CLI y ejecuta notholy login en tu terminal.

    $ notholy login