Перейти к содержимому
New

DeepSeek V4.1 Flash free for 7 days: 10M tokens a day after a top-up of $10 or more. Until Nov 30.

How it works
aeondave/renodeРеверс-инжиниринг и фаззинг

renode

⁨Auth/lab ref: Renode board and SoC simulation for MCU/RTOS firmware, UART/GPIO/peripheral modeling, GDB remote debugging, REPL platforms, and RESC scripts.⁩

v2026.11.13-21cd5683 установки+3 за 7 дней39 ЗвездыMITсинхронизировано 11 часов назад

Установка

Ещё нет NotHoly CLI? Сначала установите её.

$ curl -fsSL https://notholy.com/install.sh | sh
$ notholy skills install aeondave/renode

Пишет в ⁦~/.notholy/skills⁩ после проверки подписи и SHA-256.

ПодписьПодписано, ed25519
B5lX+w5ZXq…jG5gcCDg==CLI проверяет SHA-256 и подпись, прежде чем записать хоть один файл.
Пакетb93625da…f7992cb7
b93625da6f17…aadcf7992cb71 файл · ⁦1.8 KB⁩
ПроверкаНизкийзамечаний нет
Проверка не нашла в этой версии ничего подозрительного.Вся проверка
Источникgithub.com/AeonDave/malskill/tree/main/offensive-tools/rev/renode@21cd568

Эта запись еще не переведена на русский, поэтому показан текст на другом языке: English.

Renode is the first public tool to try when firmware behavior depends on a modeled MCU board, RTOS peripherals, UART, GPIO, timers, storage, or multi-core SoC state.

Use Renode when

  • the artifact is MCU/RTOS firmware and a board or close SoC model exists
  • UART/GPIO/timer/storage/network peripheral behavior matters
  • QEMU lacks the exact board, or CPU-only emulation hangs on MMIO
  • you need deterministic virtual time and GDB remote debugging
  • you can write or adapt a .repl platform description for the minimum needed peripherals

Do not treat CPU stepping as board parity. Prove the peripheral behavior relevant to the objective.

Core objects

  • .repl: platform description; CPUs, memory maps, buses, UARTs, GPIOs, timers, and peripherals.
  • .resc: Renode monitor script; creates machines, loads platforms, loads binaries, configures analyzers, starts emulation.
  • Monitor: interactive command surface for machines, sysbus, peripherals, memory, UART analyzers, and GDB server.
  • Robot Framework: useful for validation harnesses that assert UART/peripheral output; keep it as test infrastructure, not the only evidence.

Minimal monitor flow

text
mach create
machine LoadPlatformDescription @platforms/boards/<board>.repl
sysbus LoadELF @firmware.elf
showAnalyzer sysbus.uart0
machine StartGdbServer 3333
start

Useful commands:

text
peripherals
sysbus WhatPeripheralIsAt 0x40000000
sysbus ReadDoubleWord 0x40000000
sysbus WriteDoubleWord 0x40000000 0x1
sysbus.cpu Step
pause
quit

For raw binaries, set load address and reset vector deliberately; ELF is safer when available because it carries sections and entry point.

Custom platform guidance

When no board exists:

  1. Build the smallest .repl from known CPU, RAM/flash, and MMIO ranges.
  2. Add UART first if console output is needed.
  3. Add timers/interrupt controller before assuming RTOS scheduler failure.
  4. Stub unknown peripherals only enough to pass non-target checks.
  5. Label the result as partial parity and list unmodeled peripherals.

Sources for modeling clues: vendor datasheet, SVD, linker script, map file, DTB, SDK headers, strings, disassembly xrefs to MMIO addresses, and logic/UART captures.

GDB

text
machine StartGdbServer 3333

Then connect with the matching toolchain:

bash
arm-none-eabi-gdb firmware.elf
(gdb) target remote :3333

Use GDB to prove reset handler, RTOS task creation, peripheral driver paths, memory state, and breakpoints on fault handlers.

Evidence

  • exact .repl/.resc or monitor command sequence
  • board/profile source and any custom modeled/stubbed devices
  • UART transcript, GPIO/peripheral read/write, memory state, or GDB breakpoint
  • whether proof is instruction execution, runtime boot, peripheral parity, or system parity

Failure pivots

  • no UART: wrong UART instance, firmware uses semihosting/RTT, clocks not modeled, or boot never reaches init
  • stuck in default handler: missing IRQ/timer/peripheral model
  • fault after reset: wrong load address, vector table, stack pointer, Thumb bit, or memory map
  • GDB oddities on multicore boards: start/select the correct CPU-specific GDB server

Файлы этой версии

Права

ПравоЗаявленоНайдено проверкой
Читает файлыНетНет
Пишет файлыНетНет
Выполняет команды shellДаДа
Ходит в сетьНетНет
Использует коннекторыНетНет
Управляет браузеромНетНет

Замечания проверки

Проверено 13 нояб. 2026 г.

Проверка не нашла в этой версии ничего подозрительного.

Чистая проверка снижает риск, но не доказывает, что пакет безопасен. Читайте то, что ставите.

ВерсияОпубликованаКоммитSHA-256ПодписьИзменение прав
v2026.11.13-21cd56813 нояб. 2026 г.21cd568b93625daПодписана–

Спрашивайте обо всём, что позволяет ваш скоуп.

Создайте аккаунт, пополните баланс и задайте первый вопрос в чате или в терминале.

  1. 1/3

    Создайте аккаунт

    Личный или для компании. Позже можно перейти на аккаунт компании без потери баланса и ключей.

    ЛичныйКомпания
  2. 2/3

    Пополните баланс

    Картой. Оплата за токены, без подписки.

    $5.00минимальное пополнение
  3. 3/3

    Спрашивайте

    В чате, или установите CLI и выполните notholy login в терминале.

    $ notholy login