Pular para o conteúdo
Novo

DeepSeek V4.1 Flash grátis por 7 dias: 10M tokens por dia após recarga de $10 ou mais. Até 30/11.

Como funciona
aeondave/renodeEngenharia reversa e fuzzing

renode

⁨Auth/lab ref: Renode board and SoC simulation for MCU/RTOS firmware, UART/GPIO/peripheral modeling, GDB remote debugging, REPL platforms, and RESC scripts.⁩

v2026.11.13-21cd5683 instalações+3 em 7 dias39 EstrelasMITsincronizado há 11 horas

Instalar

Ainda não tem a CLI da NotHoly? Instale primeiro.

$ curl -fsSL https://notholy.com/install.sh | sh
$ notholy skills install aeondave/renode

Grava em ⁦~/.notholy/skills⁩ depois de conferir a assinatura e o SHA-256.

AssinaturaAssinado, ed25519
B5lX+w5ZXq…jG5gcCDg==A CLI confere o SHA-256 e a assinatura antes de gravar qualquer arquivo.
Pacoteb93625da…f7992cb7
b93625da6f17…aadcf7992cb71 arquivo · ⁦1.8 KB⁩
VarreduraBaixonenhum achado
A varredura não encontrou nada para apontar nesta versão.Ver a varredura completa
Fontegithub.com/AeonDave/malskill/tree/main/offensive-tools/rev/renode@21cd568

Este item ainda não foi escrito no seu idioma, então aparece em English.

Renode is the first public tool to try when firmware behavior depends on a modeled MCU board, RTOS peripherals, UART, GPIO, timers, storage, or multi-core SoC state.

Use Renode when

  • the artifact is MCU/RTOS firmware and a board or close SoC model exists
  • UART/GPIO/timer/storage/network peripheral behavior matters
  • QEMU lacks the exact board, or CPU-only emulation hangs on MMIO
  • you need deterministic virtual time and GDB remote debugging
  • you can write or adapt a .repl platform description for the minimum needed peripherals

Do not treat CPU stepping as board parity. Prove the peripheral behavior relevant to the objective.

Core objects

  • .repl: platform description; CPUs, memory maps, buses, UARTs, GPIOs, timers, and peripherals.
  • .resc: Renode monitor script; creates machines, loads platforms, loads binaries, configures analyzers, starts emulation.
  • Monitor: interactive command surface for machines, sysbus, peripherals, memory, UART analyzers, and GDB server.
  • Robot Framework: useful for validation harnesses that assert UART/peripheral output; keep it as test infrastructure, not the only evidence.

Minimal monitor flow

text
mach create
machine LoadPlatformDescription @platforms/boards/<board>.repl
sysbus LoadELF @firmware.elf
showAnalyzer sysbus.uart0
machine StartGdbServer 3333
start

Useful commands:

text
peripherals
sysbus WhatPeripheralIsAt 0x40000000
sysbus ReadDoubleWord 0x40000000
sysbus WriteDoubleWord 0x40000000 0x1
sysbus.cpu Step
pause
quit

For raw binaries, set load address and reset vector deliberately; ELF is safer when available because it carries sections and entry point.

Custom platform guidance

When no board exists:

  1. Build the smallest .repl from known CPU, RAM/flash, and MMIO ranges.
  2. Add UART first if console output is needed.
  3. Add timers/interrupt controller before assuming RTOS scheduler failure.
  4. Stub unknown peripherals only enough to pass non-target checks.
  5. Label the result as partial parity and list unmodeled peripherals.

Sources for modeling clues: vendor datasheet, SVD, linker script, map file, DTB, SDK headers, strings, disassembly xrefs to MMIO addresses, and logic/UART captures.

GDB

text
machine StartGdbServer 3333

Then connect with the matching toolchain:

bash
arm-none-eabi-gdb firmware.elf
(gdb) target remote :3333

Use GDB to prove reset handler, RTOS task creation, peripheral driver paths, memory state, and breakpoints on fault handlers.

Evidence

  • exact .repl/.resc or monitor command sequence
  • board/profile source and any custom modeled/stubbed devices
  • UART transcript, GPIO/peripheral read/write, memory state, or GDB breakpoint
  • whether proof is instruction execution, runtime boot, peripheral parity, or system parity

Failure pivots

  • no UART: wrong UART instance, firmware uses semihosting/RTT, clocks not modeled, or boot never reaches init
  • stuck in default handler: missing IRQ/timer/peripheral model
  • fault after reset: wrong load address, vector table, stack pointer, Thumb bit, or memory map
  • GDB oddities on multicore boards: start/select the correct CPU-specific GDB server

Arquivos desta versão

Permissões

PermissãoDeclaradaEncontrada na varredura
Lê arquivosNãoNão
Grava arquivosNãoNão
Roda comandos no shellSimSim
Usa a redeNãoNão
Usa conectoresNãoNão
Controla um navegadorNãoNão

Achados da varredura

Revisado em 13 de nov. de 2026

A varredura não encontrou nada para apontar nesta versão.

Uma varredura limpa reduz o risco, mas não prova que o pacote é seguro. Leia o que você instala.

VersãoPublicada emCommitSHA-256AssinaturaMudança de permissão
v2026.11.13-21cd56813 de nov. de 202621cd568b93625daAssinada–

Pergunte tudo o que o seu escopo permite.

Crie a conta, adicione créditos e faça a primeira pergunta no chat ou no terminal.

  1. 1/3

    Crie a conta

    Individual ou empresa. Dá para virar empresa depois sem perder saldo nem chaves.

    Pessoa físicaEmpresa
  2. 2/3

    Adicione créditos

    No cartão. Você paga por token, sem assinatura.

    $5.00recarga mínima
  3. 3/3

    Pergunte

    No chat, ou instale o CLI e rode notholy login no terminal.

    $ notholy login