Saltar al contenido
Nuevo

DeepSeek V4.1 Flash gratis por 7 días: 10M tokens al día tras una recarga de $10 o más. Hasta el 30/11.

Cómo funciona
aeondave/renodeIngeniería inversa y fuzzing

renode

⁨Auth/lab ref: Renode board and SoC simulation for MCU/RTOS firmware, UART/GPIO/peripheral modeling, GDB remote debugging, REPL platforms, and RESC scripts.⁩

v2026.11.13-21cd5683 instalaciones+3 en 7 días39 EstrellasMITsincronizado hace 11 horas

Instalar

¿Aún no tienes la CLI de NotHoly? Instálala primero.

$ curl -fsSL https://notholy.com/install.sh | sh
$ notholy skills install aeondave/renode

Escribe en ⁦~/.notholy/skills⁩ después de comprobar la firma y el SHA-256.

FirmaFirmado, ed25519
B5lX+w5ZXq…jG5gcCDg==La CLI comprueba el SHA-256 y la firma antes de escribir cualquier archivo.
Paqueteb93625da…f7992cb7
b93625da6f17…aadcf7992cb71 archivo · ⁦1.8 KB⁩
EscaneoBajosin hallazgos
El escaneo no encontró nada que señalar en esta versión.Ver el escaneo completo
Fuentegithub.com/AeonDave/malskill/tree/main/offensive-tools/rev/renode@21cd568

Esta entrada todavía no está escrita en tu idioma, así que aparece en English.

Renode is the first public tool to try when firmware behavior depends on a modeled MCU board, RTOS peripherals, UART, GPIO, timers, storage, or multi-core SoC state.

Use Renode when

  • the artifact is MCU/RTOS firmware and a board or close SoC model exists
  • UART/GPIO/timer/storage/network peripheral behavior matters
  • QEMU lacks the exact board, or CPU-only emulation hangs on MMIO
  • you need deterministic virtual time and GDB remote debugging
  • you can write or adapt a .repl platform description for the minimum needed peripherals

Do not treat CPU stepping as board parity. Prove the peripheral behavior relevant to the objective.

Core objects

  • .repl: platform description; CPUs, memory maps, buses, UARTs, GPIOs, timers, and peripherals.
  • .resc: Renode monitor script; creates machines, loads platforms, loads binaries, configures analyzers, starts emulation.
  • Monitor: interactive command surface for machines, sysbus, peripherals, memory, UART analyzers, and GDB server.
  • Robot Framework: useful for validation harnesses that assert UART/peripheral output; keep it as test infrastructure, not the only evidence.

Minimal monitor flow

text
mach create
machine LoadPlatformDescription @platforms/boards/<board>.repl
sysbus LoadELF @firmware.elf
showAnalyzer sysbus.uart0
machine StartGdbServer 3333
start

Useful commands:

text
peripherals
sysbus WhatPeripheralIsAt 0x40000000
sysbus ReadDoubleWord 0x40000000
sysbus WriteDoubleWord 0x40000000 0x1
sysbus.cpu Step
pause
quit

For raw binaries, set load address and reset vector deliberately; ELF is safer when available because it carries sections and entry point.

Custom platform guidance

When no board exists:

  1. Build the smallest .repl from known CPU, RAM/flash, and MMIO ranges.
  2. Add UART first if console output is needed.
  3. Add timers/interrupt controller before assuming RTOS scheduler failure.
  4. Stub unknown peripherals only enough to pass non-target checks.
  5. Label the result as partial parity and list unmodeled peripherals.

Sources for modeling clues: vendor datasheet, SVD, linker script, map file, DTB, SDK headers, strings, disassembly xrefs to MMIO addresses, and logic/UART captures.

GDB

text
machine StartGdbServer 3333

Then connect with the matching toolchain:

bash
arm-none-eabi-gdb firmware.elf
(gdb) target remote :3333

Use GDB to prove reset handler, RTOS task creation, peripheral driver paths, memory state, and breakpoints on fault handlers.

Evidence

  • exact .repl/.resc or monitor command sequence
  • board/profile source and any custom modeled/stubbed devices
  • UART transcript, GPIO/peripheral read/write, memory state, or GDB breakpoint
  • whether proof is instruction execution, runtime boot, peripheral parity, or system parity

Failure pivots

  • no UART: wrong UART instance, firmware uses semihosting/RTT, clocks not modeled, or boot never reaches init
  • stuck in default handler: missing IRQ/timer/peripheral model
  • fault after reset: wrong load address, vector table, stack pointer, Thumb bit, or memory map
  • GDB oddities on multicore boards: start/select the correct CPU-specific GDB server

Archivos de esta versión

Permisos

PermisoDeclaradoHallado en el escaneo
Lee archivosNoNo
Escribe archivosNoNo
Ejecuta comandos de shellSíSí
Usa la redNoNo
Usa conectoresNoNo
Controla un navegadorNoNo

Hallazgos del escaneo

Revisado el 13 nov 2026

El escaneo no encontró nada que señalar en esta versión.

Un escaneo limpio baja el riesgo, pero no prueba que el paquete sea seguro. Lee lo que instalas.

VersiónPublicadaCommitSHA-256FirmaCambio de permisos
v2026.11.13-21cd56813 nov 202621cd568b93625daFirmada–

Pregunta todo lo que tu alcance permite.

Crea la cuenta, añade créditos y haz la primera pregunta en el chat o en la terminal.

  1. 1/3

    Crea la cuenta

    Individual o empresa. Puedes pasar a empresa después sin perder saldo ni claves.

    IndividualEmpresa
  2. 2/3

    Añade créditos

    Con tarjeta. Pagas por token, sin suscripción.

    $5.00recarga mínima
  3. 3/3

    Pregunta

    En el chat, o instala el CLI y ejecuta notholy login en tu terminal.

    $ notholy login