Pular para o conteúdo
Novo

DeepSeek V4.1 Flash grátis por 7 dias: 10M tokens por dia após recarga de $10 ou mais. Até 30/11.

Como funciona
aeondave/jtag-swdMobile, firmware e hardware

jtag-swd

⁨Non-destructive JTAG/SWD pin identification, OpenOCD configuration, CPU halting, and runtime memory dumping.⁩

v2026.11.13-21cd5683 instalações+3 em 7 dias39 Estrelassincronizado há 10 horas

Instalar

Ainda não tem a CLI da NotHoly? Instale primeiro.

$ curl -fsSL https://notholy.com/install.sh | sh
$ notholy skills install aeondave/jtag-swd

Grava em ⁦~/.notholy/skills⁩ depois de conferir a assinatura e o SHA-256.

AssinaturaAssinado, ed25519
clqBlT6T3S…niiWLwDg==A CLI confere o SHA-256 e a assinatura antes de gravar qualquer arquivo.
Pacotef7d2ba46…6fc57b00
f7d2ba46a5d3…ba3c6fc57b002 arquivos · ⁦2.4 KB⁩
VarreduraMédio2 achados
  • Nenhuma licença encontrada
  • Links para domínios externos
Ver a varredura completa
Fontegithub.com/AeonDave/malskill/tree/main/offensive-hardware/jtag-swd@21cd568

Este item ainda não foi escrito no seu idioma, então aparece em English.

Use when firmware extraction is needed but direct SPI flash reading is physically impossible (BGA chips, eMMC), or live debugging/execution flow control is required.

1. Interface identification

  • Standard JTAG: TCK, TMS, TDI, TDO, nTRST, nSRST, GND, VCC.
  • ARM SWD: Compact 2-wire alternative (SWDIO, SWDCLK, GND, VCC).
  • Use tools like JTAGulator or JTAGenum on unknown pin headers to automatically scan for TDO responses without manual probing.

2. Electrical and target preflight

Before connecting, confirm the target's I/O voltage, probe voltage compatibility, supported transport (JTAG or SWD), pinout, and any required level shifting from the target and probe documentation. Do not assume VTref powers the target or has the same function on every probe; check that probe's manual before wiring or powering anything. See the OpenOCD adapter guidance.

For the original ESP32, use JTAG, not SWD. ESP-IDF v6.1 documents JTAG I/O on VDD_3P3_RTC (normally 3.3 V); ensure the adapter supports the target's I/O level. Do not generalize this pin, voltage, or transport note to other ESP32-family chips; check the exact device documentation. See ESP-IDF v6.1 JTAG debugging.

ESP-IDF v6.1 documents a configuration-dependent case where flash-encryption setup disables JTAG by burning the relevant eFuse on first boot. Check the project's flash-encryption configuration and actual eFuse state for the specific original ESP32 before expecting debug access; flash encryption alone is not evidence that this eFuse was burned. See ESP-IDF v6.1 flash encryption.

3. OpenOCD connection

Map the physical interface (e.g., FTDI-based programmer like Olimex or TIAO) and the target MCU architecture.

bash
# Example: Connect to an STM32F4 via an Olimex ARM-USB-OCD-H programmer
openocd -f interface/ftdi/olimex-arm-usb-ocd-h.cfg -f target/stm32f4x.cfg

4. Execution control & dumping

Connect to OpenOCD's telnet control interface (localhost:4444).

text
> telnet localhost 4444
# Halt the CPU execution cleanly
> halt

# Inspect CPU state and registers
> reg

# Dump specific memory region (e.g., 1MB starting from flash base 0x08000000)
> dump_image firmware.bin 0x08000000 0x100000

# Resume normal execution
> resume

5. Risks & Considerations

  • Watchdog Timers: Halting via JTAG may trigger hardware watchdogs, causing abrupt resets.
  • Read-out Protection (RDP): Microcontrollers (especially STM32/NRF) often set internal fuses disabling JTAG debug access or flash reads. Bypassing requires chip-specific glitching workflows.

References

  • references/stm32-rdp-bypass.md — Load when an STM32 Read-Out Protection (RDP) prevents memory extraction in OpenOCD.

Arquivos desta versão

Permissões

PermissãoDeclaradaEncontrada na varredura
Lê arquivosNãoNão
Grava arquivosNãoNão
Roda comandos no shellSimSim
Usa a redeSimSim
Usa conectoresNãoNão
Controla um navegadorNãoNão

Achados da varredura

Revisado em 13 de nov. de 2026

  1. MédiaLicença · Nenhuma licença encontrada
  2. InfoLink · Links para domínios externos

Uma varredura limpa reduz o risco, mas não prova que o pacote é seguro. Leia o que você instala.

VersãoPublicada emCommitSHA-256AssinaturaMudança de permissão
v2026.11.13-21cd56813 de nov. de 202621cd568f7d2ba46Assinada–

Pergunte tudo o que o seu escopo permite.

Crie a conta, adicione créditos e faça a primeira pergunta no chat ou no terminal.

  1. 1/3

    Crie a conta

    Individual ou empresa. Dá para virar empresa depois sem perder saldo nem chaves.

    Pessoa físicaEmpresa
  2. 2/3

    Adicione créditos

    No cartão. Você paga por token, sem assinatura.

    $5.00recarga mínima
  3. 3/3

    Pergunte

    No chat, ou instale o CLI e rode notholy login no terminal.

    $ notholy login