דילוג לתוכן
New

DeepSeek V4.1 Flash free for 7 days: 10M tokens a day after a top-up of $10 or more. Until Nov 30.

How it works
aeondave/jtag-swdמובייל, קושחה וחומרה

jtag-swd

⁨Non-destructive JTAG/SWD pin identification, OpenOCD configuration, CPU halting, and runtime memory dumping.⁩

v2026.11.13-21cd5683 התקנות⁦+3⁩ ב-7 ימים39 כוכביםסונכרן לפני 11 שעות

התקנה

עדיין אין לכם את ה-CLI של NotHoly? התקינו אותו קודם.

$ curl -fsSL https://notholy.com/install.sh | sh
$ notholy skills install aeondave/jtag-swd

נכתב אל ⁦~/.notholy/skills⁩ אחרי בדיקת החתימה וה-SHA-256.

חתימהחתום, ed25519
clqBlT6T3S…niiWLwDg==ה-CLI בודק את ה-SHA-256 ואת החתימה לפני שהוא כותב קובץ כלשהו.
חבילהf7d2ba46…6fc57b00
f7d2ba46a5d3…ba3c6fc57b00שני קבצים · ⁦2.4 KB⁩
סריקהבינונישני ממצאים
  • לא נמצא רישיון
  • קישורים לדומיינים חיצוניים
לסריקה המלאה
מקורgithub.com/AeonDave/malskill/tree/main/offensive-hardware/jtag-swd@21cd568

הפריט הזה עדיין לא נכתב בעברית, ולכן הוא מוצג בשפה אחרת: English.

Use when firmware extraction is needed but direct SPI flash reading is physically impossible (BGA chips, eMMC), or live debugging/execution flow control is required.

1. Interface identification

  • Standard JTAG: TCK, TMS, TDI, TDO, nTRST, nSRST, GND, VCC.
  • ARM SWD: Compact 2-wire alternative (SWDIO, SWDCLK, GND, VCC).
  • Use tools like JTAGulator or JTAGenum on unknown pin headers to automatically scan for TDO responses without manual probing.

2. Electrical and target preflight

Before connecting, confirm the target's I/O voltage, probe voltage compatibility, supported transport (JTAG or SWD), pinout, and any required level shifting from the target and probe documentation. Do not assume VTref powers the target or has the same function on every probe; check that probe's manual before wiring or powering anything. See the OpenOCD adapter guidance.

For the original ESP32, use JTAG, not SWD. ESP-IDF v6.1 documents JTAG I/O on VDD_3P3_RTC (normally 3.3 V); ensure the adapter supports the target's I/O level. Do not generalize this pin, voltage, or transport note to other ESP32-family chips; check the exact device documentation. See ESP-IDF v6.1 JTAG debugging.

ESP-IDF v6.1 documents a configuration-dependent case where flash-encryption setup disables JTAG by burning the relevant eFuse on first boot. Check the project's flash-encryption configuration and actual eFuse state for the specific original ESP32 before expecting debug access; flash encryption alone is not evidence that this eFuse was burned. See ESP-IDF v6.1 flash encryption.

3. OpenOCD connection

Map the physical interface (e.g., FTDI-based programmer like Olimex or TIAO) and the target MCU architecture.

bash
# Example: Connect to an STM32F4 via an Olimex ARM-USB-OCD-H programmer
openocd -f interface/ftdi/olimex-arm-usb-ocd-h.cfg -f target/stm32f4x.cfg

4. Execution control & dumping

Connect to OpenOCD's telnet control interface (localhost:4444).

text
> telnet localhost 4444
# Halt the CPU execution cleanly
> halt

# Inspect CPU state and registers
> reg

# Dump specific memory region (e.g., 1MB starting from flash base 0x08000000)
> dump_image firmware.bin 0x08000000 0x100000

# Resume normal execution
> resume

5. Risks & Considerations

  • Watchdog Timers: Halting via JTAG may trigger hardware watchdogs, causing abrupt resets.
  • Read-out Protection (RDP): Microcontrollers (especially STM32/NRF) often set internal fuses disabling JTAG debug access or flash reads. Bypassing requires chip-specific glitching workflows.

References

  • references/stm32-rdp-bypass.md — Load when an STM32 Read-Out Protection (RDP) prevents memory extraction in OpenOCD.

הקבצים בגרסה הזו

הרשאות

הרשאההוצהרנמצא בסריקה
קורא קבציםלאלא
כותב קבציםלאלא
מריץ פקודות shellכןכן
משתמש ברשתכןכן
משתמש במחבריםלאלא
שולט בדפדפןלאלא

ממצאי הסריקה

נבדק ב-13 בנוב׳ 2026

  1. בינוניתרישיון · לא נמצא רישיון
  2. מידעקישור · קישורים לדומיינים חיצוניים

סריקה נקייה מורידה את הסיכון, אבל לא מוכיחה שהחבילה בטוחה. כדאי לקרוא מה מתקינים.

גרסהפורסמהCommitSHA-256חתימהשינוי בהרשאות
v2026.11.13-21cd56813 בנוב׳ 202621cd568f7d2ba46חתומה–

שאלו כל מה שהסקופ מאפשר.

יוצרים חשבון, מוסיפים קרדיטים ושואלים את השאלה הראשונה בצ׳אט או בטרמינל.

  1. 1/3

    יצירת חשבון

    פרטי או חברה. אפשר לעבור לחשבון חברה אחר כך בלי לאבד יתרה או מפתחות.

    פרטיחברה
  2. 2/3

    הוספת קרדיטים

    בכרטיס אשראי. תשלום לפי טוקן, בלי מנוי.

    $5.00טעינה מינימלית
  3. 3/3

    שאלה ראשונה

    בצ׳אט, או להתקין את ה-CLI ולהריץ notholy login בטרמינל.

    $ notholy login