Saltar al contenido
Nuevo

DeepSeek V4.1 Flash gratis por 7 días: 10M tokens al día tras una recarga de $10 o más. Hasta el 30/11.

Cómo funciona
aeondave/can-bus-modulesMóvil, firmware y hardware

can-bus-modules

⁨CAN Bus interfacing for automotive/industrial networks using MCP2515 over SPI, baud rates, reading OBD-II frames.⁩

v2026.11.13-21cd5683 instalaciones+3 en 7 días39 Estrellassincronizado hace 10 horas

Instalar

¿Aún no tienes la CLI de NotHoly? Instálala primero.

$ curl -fsSL https://notholy.com/install.sh | sh
$ notholy skills install aeondave/can-bus-modules

Escribe en ⁦~/.notholy/skills⁩ después de comprobar la firma y el SHA-256.

FirmaFirmado, ed25519
b6Rbre1WT/…0QI1N6CQ==La CLI comprueba el SHA-256 y la firma antes de escribir cualquier archivo.
Paquete3cd32375…c5ad6f2f
3cd32375f1af…7647c5ad6f2f1 archivo · ⁦1.3 KB⁩
EscaneoMedio1 hallazgo
  • No se encontró licencia
Ver el escaneo completo
Fuentegithub.com/AeonDave/malskill/tree/main/hardware/can-bus-modules@21cd568

Esta entrada todavía no está escrita en tu idioma, así que aparece en English.

Goal: Interface microcontrollers with automotive and industrial Controller Area Networks (CAN) using transceivers to read and spoof packets.

1. Hardware Stack

  • MCU: e.g., Arduino or ESP32.
  • Controller: MCP2515 (Translates SPI from MCU into CAN format). Maintains transmit buffers and acceptance filters.
  • Transceiver: TJA1050 or MCP2551 (Translates logic-level CAN from the MCP2515 into the differential CAN_H and CAN_L analog voltages required by the physical bus).
  • Physical Bus: CAN_H and CAN_L twisted pair. Requires 120-ohm termination resistors at both ends of the bus.

2. Setting Baud Rates & Oscillators

The CAN bus relies entirely on timing. Connecting with the wrong speed brings down the bus (Error Passive).

  • Standard OBD-II in vehicles uses 500 kbps.
  • Slower comfort buses (doors, windows) might use 125 kbps or 250 kbps.
  • Make sure you initialize the library with the exact crystal oscillator speed attached to your MCP2515 board (commonly 8 MHz or 16 MHz).

3. Standard vs Extended Frames

  • Standard Frame: 11-bit ID. (e.g., 0x7DF). Used heavily in standard automotive.
  • Extended Frame: 29-bit ID. (e.g., 0x18DAF100). Often seen in heavy duty (J1939) or specialized sensors.
  • Payload is always 0 to 8 bytes.

4. Code Snapshot (mcp_can library)

cpp
#include <SPI.h>
#include <mcp_can.h>

const int spiCSPin = 10;
MCP_CAN CAN(spiCSPin);

void setup() {
    Serial.begin(115200);
    // Initialize exactly for 500k baud and 8MHz crystal
    while (CAN_OK != CAN.begin(CAN_500KBPS, MCP_8MHz)) {
        Serial.println("CAN init fail, retry...");
        delay(100);
    }
    Serial.println("CAN init ok!");
}

void loop() {
    long unsigned int rxId;
    unsigned char len = 0;
    unsigned char rxBuf[8];

    if (CAN_MSGAVAIL == CAN.checkReceive()) {
        CAN.readMsgBuf(&rxId, &len, rxBuf);
        Serial.print("ID: "); Serial.print(rxId, HEX);
        Serial.print(" Data: ");
        for(int i = 0; i<len; i++) {
            Serial.print(rxBuf[i], HEX); Serial.print(" ");
        }
        Serial.println();
    }
}

Archivos de esta versión

Permisos

PermisoDeclaradoHallado en el escaneo
Lee archivosNoNo
Escribe archivosNoNo
Ejecuta comandos de shellNoNo
Usa la redNoNo
Usa conectoresNoNo
Controla un navegadorNoNo

Hallazgos del escaneo

Revisado el 13 nov 2026

  1. MediaLicencia · No se encontró licencia

Un escaneo limpio baja el riesgo, pero no prueba que el paquete sea seguro. Lee lo que instalas.

VersiónPublicadaCommitSHA-256FirmaCambio de permisos
v2026.11.13-21cd56813 nov 202621cd5683cd32375Firmada–

Pregunta todo lo que tu alcance permite.

Crea la cuenta, añade créditos y haz la primera pregunta en el chat o en la terminal.

  1. 1/3

    Crea la cuenta

    Individual o empresa. Puedes pasar a empresa después sin perder saldo ni claves.

    IndividualEmpresa
  2. 2/3

    Añade créditos

    Con tarjeta. Pagas por token, sin suscripción.

    $5.00recarga mínima
  3. 3/3

    Pregunta

    En el chat, o instala el CLI y ejecuta notholy login en tu terminal.

    $ notholy login