Перейти к содержимому
New

DeepSeek V4.1 Flash free for 7 days: 10M tokens a day after a top-up of $10 or more. Until Nov 30.

How it works
noorqureshi/hardware-securityМобильные устройства, прошивки и железо

hardware-security

⁨Discover and triage hardware debug interfaces (UART, JTAG, SWD) on an authorized embedded device — read boot logs, land a root console, interrupt the bootloader, and extract flash for offline analysis. Load when handed a physical device, PCB, or IoT/embedded target in scope, exposed test points or h⁩

v2026.10.14-ee0e0c53 установки+3 за 7 дней27 ЗвездыMITсинхронизировано 22 часа назад

Установка

Ещё нет NotHoly CLI? Сначала установите её.

$ curl -fsSL https://notholy.com/install.sh | sh
$ notholy skills install noorqureshi/hardware-security

Пишет в ⁦~/.notholy/skills⁩ после проверки подписи и SHA-256.

ПодписьПодписано, ed25519
dAmVbvhV+D…/towHJBw==CLI проверяет SHA-256 и подпись, прежде чем записать хоть один файл.
Пакет5985b2f2…13cef323
5985b2f2a079…f36313cef3231 файл · ⁦2.8 KB⁩
ПроверкаНизкий1 замечание
  • Ссылки на внешние домены
Вся проверка
Источникgithub.com/NoorQureshi/security-skills/tree/main/skills/hardware/hardware-security@ee0e0c5

Эта запись еще не переведена на русский, поэтому показан текст на другом языке: English.

When it applies

You have physical access to a device you own or are explicitly authorized to open — a router, IoT gadget, embedded controller, or a board pulled from a larger system — and you need console access or a firmware image. Hardware work is governed by the same envelope as everything else: load tradecraft-scope-roe first and confirm the physical device and the teardown itself are in scope.txt. Never open or probe a device that isn't yours or in writing.

Why it works

Vendors leave debug and factory-test interfaces on the board: a UART serial console for boot logs (often a root shell), and JTAG/SWD for chip-level debugging and memory readout. These ports bypass all software authentication on the running system — if you can electrically reach them and match the logic levels, the device talks to you. Bootloader consoles (U-Boot) additionally let you alter boot arguments or read flash before the OS locks anything down.

Method

  1. Open, photograph, label. Photograph both board sides before touching anything; note silkscreen near pad clusters: TX RX GND VCC (UART) and TDI TDO TCK TMS (JTAG), SWDIO/SWCLK (SWD). Mind ESD — ground yourself; default to read-only probing.
  2. Identify the UART pinout with a multimeter, not guesses. Find GND (continuity to a shield or ground pour), VCC (stable rail at power-on), TX (pulses during boot — confirm with a logic analyzer if ambiguous), RX (floating/pulled line next to TX). Measure the logic level first — 1.8 V, 3.3 V, or 5 V — and match your adapter to it before connecting anything.
  3. Attach read-only first. Connect only GND + the board's TX to a USB-TTL adapter and watch the boot log: screen /dev/ttyUSB0 115200 (or minicom). If the output is garbage, sweep common baud rates (9600/38400/57600/115200) until the log is legible; record the rate. Boot logs alone leak flash layout, kernel version, and often credentials.
  4. Work the console. Many devices drop to a root shell with no password. Interrupt U-Boot at the countdown (usually any key) and dump printenv — note the environment, but do not saveenv casually: a wrong write bricks the boot.
  5. Probe JTAG/SWD if UART is dead or locked. With a J-Link or CMSIS-DAP adapter under OpenOCD, enumerate the chain and read the IDCODE: openocd -f interface/jlink.cfg -f target/<chip>.cfg. A populated IDCODE means the debug port is live; an all-zeros/all-ones response means it's fused off or your wiring/level is wrong.
  6. Extract flash for offline analysis. In-circuit SPI dumps with a cheap programmer: flashrom -p ch341a_spi -r dump.bin (verify with a second dump and compare hashes). Immediately record shasum -a 256 dump.bin for evidence integrity, then hand the image to reverse-eng-firmware for extraction and analysis; individual binaries go to reverse-eng-binary-triage.
  7. Assess secure-boot/encrypted-flash feasibility non-destructively first (signed-image checks in the boot log, eFuse hints from JTAG behavior) before considering chip-off or glitching — those are destructive and need explicit sign-off.

Gotchas

  • Wrong logic level kills ports. Connecting a 5 V adapter to a 1.8 V UART can destroy the SoC pins. Measure first; use a level shifter when in doubt.
  • Garbage output ≠ no console — it's usually the wrong baud rate. Sweep before concluding the port is mute. Truly silent UARTs may be disabled in firmware; fall back to JTAG.
  • TX/RX are named from the board's perspective — your adapter's RX listens to the board's TX. Read-only logging only needs GND + board TX.
  • A locked JTAG (empty IDCODE) is a finding too — it tells you the vendor spent effort on debug-lockout, which shapes the rest of the assessment (chip-off vs. software attack surface).
  • Every write is a bricking risk. saveenv, flash erase/program, and eFuse operations are one-way doors; get explicit approval and a verified dump before any of them.

Verify success

You have a labeled pinout photo with measured logic levels, the recorded baud rate, and at least one of: a working console (shell or U-Boot prompt), a live JTAG/SWD chain (valid IDCODE), or a SHA256-hashed flash dump ready for reverse-eng-firmware. If everything is locked, you can state precisely which interfaces exist and how each is disabled — that negative result is deliverable.

References

OpenOCD and flashrom documentation; reverse-eng-firmware for what to do with the dump.


Portions adapted from reverse-skill by zhaoxuya520, MIT License.

Файлы этой версии

Права

ПравоЗаявленоНайдено проверкой
Читает файлыНетНет
Пишет файлыНетНет
Выполняет команды shellНетНет
Ходит в сетьДаДа
Использует коннекторыНетНет
Управляет браузеромНетНет

Замечания проверки

Проверено 13 нояб. 2026 г.

  1. ИнфоСсылка · Ссылки на внешние домены

Чистая проверка снижает риск, но не доказывает, что пакет безопасен. Читайте то, что ставите.

ВерсияОпубликованаКоммитSHA-256ПодписьИзменение прав
v2026.10.14-ee0e0c513 нояб. 2026 г.ee0e0c55985b2f2Подписана–

Спрашивайте обо всём, что позволяет ваш скоуп.

Создайте аккаунт, пополните баланс и задайте первый вопрос в чате или в терминале.

  1. 1/3

    Создайте аккаунт

    Личный или для компании. Позже можно перейти на аккаунт компании без потери баланса и ключей.

    ЛичныйКомпания
  2. 2/3

    Пополните баланс

    Картой. Оплата за токены, без подписки.

    $5.00минимальное пополнение
  3. 3/3

    Спрашивайте

    В чате, или установите CLI и выполните notholy login в терминале.

    $ notholy login