Перейти к содержимому
New

DeepSeek V4.1 Flash free for 7 days: 10M tokens a day after a top-up of $10 or more. Until Nov 30.

How it works
aeondave/unicornРеверс-инжиниринг и фаззинг

unicorn

⁨Auth/lab ref: Unicorn Engine CPU-only emulation for shellcode, decryptors, custom VM handlers, instruction tracing, memory hooks, and register-level experiments.⁩

v2026.11.13-21cd5683 установки+3 за 7 дней39 ЗвездыMITсинхронизировано 11 часов назад

Установка

Ещё нет NotHoly CLI? Сначала установите её.

$ curl -fsSL https://notholy.com/install.sh | sh
$ notholy skills install aeondave/unicorn

Пишет в ⁦~/.notholy/skills⁩ после проверки подписи и SHA-256.

ПодписьПодписано, ed25519
1WKWf+w6Wc…AAZvtFBA==CLI проверяет SHA-256 и подпись, прежде чем записать хоть один файл.
Пакет0d1ceacb…cce63b7c
0d1ceacb0277…0769cce63b7c1 файл · ⁦1.4 KB⁩
ПроверкаНизкийзамечаний нет
Проверка не нашла в этой версии ничего подозрительного.Вся проверка
Источникgithub.com/AeonDave/malskill/tree/main/offensive-tools/rev/unicorn@21cd568

Эта запись еще не переведена на русский, поэтому показан текст на другом языке: English.

Unicorn is a CPU emulator. It is the right tool when you can define memory, registers, and stop conditions yourself.

Use Unicorn when

  • the target is shellcode, a decoder, checksum loop, custom VM handler, crypto primitive, or small boot stub
  • OS behavior would be noise
  • you know or can infer load address, entry address, mapped memory, stack, registers, and inputs
  • memory/register hooks are the evidence you need

Do not use Unicorn as a shortcut for real userland execution. If the target needs syscalls, files, dynamic linking, registry, interrupts, or hardware peripherals, use Qiling, QEMU, or Renode instead.

Setup checklist

  • architecture, mode, endian, ARM/Thumb state
  • code mapping address and permissions
  • stack address and size
  • input buffers and output buffers
  • initial registers and calling convention
  • imported function stubs or syscall stop points
  • maximum instruction count or address stop

Hook strategy

Hook Use
basic block coverage, control-flow sketch, custom VM dispatch
instruction exact trace, self-modifying code, privileged instruction stop
memory read/write watchpoints, decrypted output, MMIO discovery
unmapped memory identify missing mapping, import thunk, stack growth, bad pointer
interrupt/syscall stop or fake external behavior

Keep hooks narrow. Broad instruction hooks over large regions can make emulation painfully slow.

Good targets

  • XOR/RC4/AES wrapper that fills a plaintext buffer
  • password checker inner loop
  • architecture-specific shellcode decoder
  • VM bytecode dispatcher over a byte array
  • bare-metal reset stub before first peripheral wait
  • opaque predicate or anti-debug gadget

Bad targets

  • dynamically linked application with many libc calls
  • Windows or macOS binary that needs real APIs
  • Linux service that opens files, forks, listens on sockets, or uses /proc
  • MCU firmware stuck in timer/UART/GPIO MMIO loops unless those reads/writes are stubbed deliberately
  • kernel boot, drivers, or interrupt-heavy RTOS behavior

Evidence

  • initial register/memory state
  • hook outputs and stop reason
  • memory dump of transformed buffers
  • branch or address coverage proving the target path
  • exact stubs used for external calls

State clearly that the proof is CPU-level unless OS or board behavior was validated elsewhere.

Файлы этой версии

Права

ПравоЗаявленоНайдено проверкой
Читает файлыНетНет
Пишет файлыНетНет
Выполняет команды shellНетНет
Ходит в сетьНетНет
Использует коннекторыНетНет
Управляет браузеромНетНет

Замечания проверки

Проверено 13 нояб. 2026 г.

Проверка не нашла в этой версии ничего подозрительного.

Чистая проверка снижает риск, но не доказывает, что пакет безопасен. Читайте то, что ставите.

ВерсияОпубликованаКоммитSHA-256ПодписьИзменение прав
v2026.11.13-21cd56813 нояб. 2026 г.21cd5680d1ceacbПодписана–

Спрашивайте обо всём, что позволяет ваш скоуп.

Создайте аккаунт, пополните баланс и задайте первый вопрос в чате или в терминале.

  1. 1/3

    Создайте аккаунт

    Личный или для компании. Позже можно перейти на аккаунт компании без потери баланса и ключей.

    ЛичныйКомпания
  2. 2/3

    Пополните баланс

    Картой. Оплата за токены, без подписки.

    $5.00минимальное пополнение
  3. 3/3

    Спрашивайте

    В чате, или установите CLI и выполните notholy login в терминале.

    $ notholy login