Saltar al contenido
Nuevo

DeepSeek V4.1 Flash gratis por 7 días: 10M tokens al día tras una recarga de $10 o más. Hasta el 30/11.

Cómo funciona
aeondave/spi-flashMóvil, firmware y hardware

spi-flash

⁨In-circuit and out-of-circuit SPI/NAND flash dumping and writing using flashrom and CH341A/FT232H.⁩

v2026.11.13-21cd5683 instalaciones+3 en 7 días39 Estrellassincronizado hace 10 horas

Instalar

¿Aún no tienes la CLI de NotHoly? Instálala primero.

$ curl -fsSL https://notholy.com/install.sh | sh
$ notholy skills install aeondave/spi-flash

Escribe en ⁦~/.notholy/skills⁩ después de comprobar la firma y el SHA-256.

FirmaFirmado, ed25519
v5XyOWYRGA…fXEtnnBA==La CLI comprueba el SHA-256 y la firma antes de escribir cualquier archivo.
Paquete96823dca…0ef16f49
96823dca88f9…d17a0ef16f492 archivos · ⁦1.6 KB⁩
EscaneoMedio1 hallazgo
  • No se encontró licencia
Ver el escaneo completo
Fuentegithub.com/AeonDave/malskill/tree/main/offensive-hardware/spi-flash@21cd568

Esta entrada todavía no está escrita en tu idioma, así que aparece en English.

Use when UART is unavailable, or a full firmware extraction/patching loop is required.

1. Identification and connection

  • Look for 8-pin or 16-pin SOIC chips near the SoC (e.g., Winbond W25Q*, Macronix MX25L* or GigaDevice GD25Q*).
  • In-circuit: Attach a SOIC clip. Ensure the target board is completely powered off to prevent SoC interference.
  • Out-of-circuit: Desolder using hot air, clean pads, mount in programming socket. (Safest for signal integrity, but destructive).

2. Reading firmware (flashrom)

Rule: Read at least twice, and ensure hashes match before proceeding. Variance indicates bad clip contact or SoC contention.

bash
# Read attempt 1
flashrom -p ch341a_spi -r fw_dump1.bin

# Read attempt 2
flashrom -p ch341a_spi -r fw_dump2.bin

# Verification
md5sum fw_dump1.bin fw_dump2.bin

If hashes differ, reseat the clip, shorten cables, or power the target board VCC slightly if SoC is draining programmer current.

3. Writing firmware

Rule: Always backup original raw dump offline before writing.

bash
# Write modified firmware back
flashrom -p ch341a_spi -w fw_patched.bin

4. Flash layout verification

Use binwalk to verify the read was successful and contains expected headers (not just 0xFF or 0x00).

bash
binwalk fw_dump1.bin
# Expect: U-Boot header, Squashfs, JFFS2, TRX, or CramFS

References

  • references/ch341a-voltage-fix.md — Load when using a CH341A programmer on 1.8V or 3.3V target flash chips.

Archivos de esta versión

Permisos

PermisoDeclaradoHallado en el escaneo
Lee archivosNoNo
Escribe archivosNoNo
Ejecuta comandos de shellSíSí
Usa la redNoNo
Usa conectoresNoNo
Controla un navegadorNoNo

Hallazgos del escaneo

Revisado el 13 nov 2026

  1. MediaLicencia · No se encontró licencia

Un escaneo limpio baja el riesgo, pero no prueba que el paquete sea seguro. Lee lo que instalas.

VersiónPublicadaCommitSHA-256FirmaCambio de permisos
v2026.11.13-21cd56813 nov 202621cd56896823dcaFirmada–

Pregunta todo lo que tu alcance permite.

Crea la cuenta, añade créditos y haz la primera pregunta en el chat o en la terminal.

  1. 1/3

    Crea la cuenta

    Individual o empresa. Puedes pasar a empresa después sin perder saldo ni claves.

    IndividualEmpresa
  2. 2/3

    Añade créditos

    Con tarjeta. Pagas por token, sin suscripción.

    $5.00recarga mínima
  3. 3/3

    Pregunta

    En el chat, o instala el CLI y ejecuta notholy login en tu terminal.

    $ notholy login